1755031114, 175-50-31114 EQUALIZER KOMATSU

When a crawler dozer is pushing hard, the undercarriage is doing far more than simply rolling. It is constantly absorbing shock loads, transferring weight, and keeping the track frame stable as the machine climbs, turns, and works across uneven ground. The 1755031114 / 175-50-31114 EQUALIZER KOMATSU is a heavy-duty structural component designed to help control track-frame movement and distribute load more evenly through the front-end undercarriage geometry. In real terms, it’s one of the parts that helps your machine feel “tight” and predictable instead of loose, noisy, and unstable.

At 3GEN Export, we supply the 175-50-31114 EQUALIZER KOMATSU as an OEM-grade replacement built for demanding job sites where impact, vibration, and continuous operation are normal—not exceptional. Every shipment is prepared for export handling, and we deliver worldwide in 5 working days so your machine downtime stays short and your operations stay on schedule.

This product page is written for buyers who want more than a one-line listing. If you’re planning a rebuild, managing a fleet, or sourcing parts for a service project, the details below will help you confirm fitment, understand what the component does, and install it correctly.

What the 175-50-31114 EQUALIZER KOMATSU does in the undercarriage

The equalizer bar sits within the front undercarriage structure and is engineered to balance and share load between left and right track frames. While exact layout varies by machine configuration, the practical goal is the same: reduce uneven stress, stabilize track-frame articulation, and help protect surrounding components from shock transfer.

On working equipment, forces rarely arrive gently. A dozer can strike packed material, climb over rock, drop into ruts, or pivot while pushing. Those actions generate twisting loads that travel through the track frames and into the chassis. The 1755031114 / 175-50-31114 EQUALIZER KOMATSU is designed to carry and distribute those loads so that stress is not concentrated where it causes premature wear or structural fatigue.

Common operational outcomes when the equalizer system is in good condition include:

• More stable tracking over uneven terrain

• Reduced shock transfer into adjacent undercarriage elements

• Improved “feel” during turning and pushing

• Less chance of accelerated wear caused by misalignment or looseness

If the equalizer system is worn, a machine may show symptoms such as clunking noises, uneven track-frame behavior, visible movement at joints, or unusual wear patterns around bushings and pins. Replacing the 175-50-31114 EQUALIZER KOMATSU at the right time helps restore structural integrity and protect the investment you already have in rollers, idlers, track groups, and frame components.

Key design features visible in the product

From the photos you shared, the component is a robust, one-piece bar with a central bore point and a heavy cross-section. That geometry is not cosmetic—mass and section thickness are necessary to resist bending loads and repeated impact cycles. The paint finish and protective packing indicate it is prepared for storage and export handling.

Typical engineering priorities for an equalizer-bar component like 1755031114 and 175 50 31114 include:

• High structural rigidity to resist deflection

• Accurate machining at bores and mounting interfaces

• Stable dimensions for consistent alignment during assembly

• Durable surface protection to handle real-world environments

Even small deviations in bore alignment or contact surfaces can create assembly stress, difficult installation, and early wear. That’s why a well-built 175-50-31114 EQUALIZER KOMATSU is not just “a bar”—it is a precision structural part that must seat correctly, carry load correctly, and remain stable over long operating hours.

Why OEM-grade build quality matters for 1755031114 / 175-50-31114

Equalizer bars operate in a high-load zone where bending forces, vibration, and shock are constant. A cheaper substitute might look similar in a photo, but small differences in material quality, heat treatment approach, or machining precision can show up later as:

• Faster wear at mounting points

• Loose fitment that increases noise and vibration

• Stress cracks around high-load transitions

• Alignment issues that accelerate wear in nearby components

The 1755031114 / 175-50-31114 EQUALIZER KOMATSU supplied by 3GEN Export is selected to match OEM expectations for durability and fit. For fleet owners, that means fewer repeat repairs. For service teams, that means fewer installation surprises. For procurement, it means a better total cost of ownership because the part is built for the environment it actually works in.

When to replace the 175-50-31114 EQUALIZER KOMATSU

Many operators wait until the problem becomes loud or visible. But structural parts like an equalizer bar often fail gradually through wear at interfaces rather than sudden breakage. Consider replacement when you notice:

• Repeated metal-on-metal noises near the front undercarriage

• Increased play in the equalizer system during inspection

• Uneven wear patterns on undercarriage components

• Changes in tracking stability, especially on uneven ground

• Evidence of impact damage or deformation

If your maintenance schedule includes undercarriage inspections, the equalizer system should be checked alongside rollers, idlers, and track tension. Addressing 1755031114 / 175-50-31114 EQUALIZER KOMATSU replacement early can help prevent secondary wear that becomes more expensive than the part itself.

Installation overview for 1755031114 / 175-50-31114 EQUALIZER KOMATSU

Equalizer-bar replacement is a heavy mechanical job. It requires safe lifting, proper support, and careful alignment. The steps below are a practical installation outline; exact procedures should follow your machine’s service manual and safety requirements.

Tools and preparation

• Suitable lifting equipment rated for heavy steel components

• Proper supports/stands for safe undercarriage positioning

• Torque tools to meet assembly specs

• Cleaning tools for bores and seating surfaces

• Inspection tools for measuring wear at mating components

Before installing the 175-50-31114 EQUALIZER KOMATSU, clean all contact areas and inspect related parts (pins, bushings, mounts, brackets). Installing a new bar into a worn interface can reduce the benefit of the replacement.

Removal steps

1. Park the machine on stable, level ground and secure it safely.

2. Relieve load and position undercarriage to allow access.

3. Support the assembly to avoid sudden movement when fasteners are removed.

4. Remove retaining hardware according to the service procedure.

5. Extract the old component carefully and inspect for deformation or wear marks that indicate underlying issues.

Installation steps

1. Confirm the part number: 1755031114 / 175-50-31114 and verify orientation.

2. Clean and lightly prepare surfaces to ensure proper seating.

3. Position the 175-50-31114 EQUALIZER KOMATSU using controlled lifting—avoid impacts that can damage edges.

4. Align bores and mounts gradually. Forcing alignment can create stress and future wear.

5. Install hardware and tighten per specification (use the correct sequence and torque values).

6. Perform a final check for free movement where applicable, and confirm there is no binding.

Post-install checks

• Run the machine at low load initially and listen for abnormal noises

• Recheck fasteners after initial operating hours if your maintenance standard requires it

• Inspect adjacent components to ensure alignment and load distribution look normal

A correctly installed 1755031114 / 175-50-31114 EQUALIZER KOMATSU should sit cleanly, align without forcing, and support stable movement under operating conditions.

Performance advantages after replacement

Replacing a worn equalizer component can make a machine feel noticeably more controlled. Depending on the condition of the removed part and associated interfaces, customers typically report improvements such as:

• Better tracking stability across uneven ground

• Reduced clunking and vibration near the undercarriage

• More consistent load distribution during pushing

• Less shock transfer into neighboring components

Because the equalizer system influences how forces travel through the undercarriage, restoring it with a solid, correctly machined 175-50-31114 EQUALIZER KOMATSU often protects other wear items from being punished by misalignment and looseness.

Compatibility: Komatsu models that commonly use this type of equalizer bar

I can’t browse the internet from this workspace, so I’m not going to claim an exact model list without a parts book reference. However, the 175-prefix part family is commonly associated with Komatsu crawler dozer undercarriage assemblies in the D155 class range and related configurations.

Typical applications to cross-check in your EPC/parts manual include:

• Komatsu D155-series crawler dozers (various variants)

• Related undercarriage configurations sharing the 175-50-31114 specification

Best practice: confirm using one of the following methods before ordering:

• Match the part number 1755031114 and 175-50-31114 in your parts catalog

• Confirm by serial number range in the EPC

• Have your service team verify dimensions and mounting configuration

If you share your machine model + serial range, I can format a cleaner “confirmed fitment” section for your listing using your internal catalog data.

Estimated weight (shipping planning)

Because weight varies by production spec and configuration, I’ll label this transparently as an estimate based on typical equalizer bar size and mass class.

Estimated net weight for 1755031114 / 175-50-31114 EQUALIZER KOMATSU: approximately 330 kg.

For accurate freight rating, 3GEN Export can confirm packing dimensions and final shipping weight at the time of dispatch.

Packaging and global delivery by 3GEN Export

A structural part like the 175-50-31114 EQUALIZER KOMATSU must arrive ready to install—not scraped, bent, or poorly protected. That’s why export-grade packing matters. Your images show the component in a timber crate with protective wrap, which is the right approach for heavy steel parts moving through ports, forklifts, and long-distance transit.

When you buy from 3GEN Export, you’re working with an OEM supplier focused on:

• Proper handling for heavy components

• Export-ready packaging suitable for international freight

• Clear documentation support for global shipments

• Worldwide delivery in 5 working days

If your buyer requires special packing instructions (extra bracing, moisture protection, labeling, multi-part consolidation), we can support that as part of professional export preparation.

Buying guide: how to order the correct part the first time

For procurement teams and service managers, ordering accuracy is everything. Before placing the order for 1755031114 / 175-50-31114 EQUALIZER KOMATSU, confirm these points:

• Part number format match: 1755031114 and 175-50-31114

• Machine model and serial range verification

• Left/right or orientation requirements (if applicable)

• Associated hardware condition (pins, bushings, retainers)

• Your preferred freight method and destination requirements

If you’re doing a larger rebuild, it can be cost-effective to bundle related items in the same shipment to reduce downtime and logistics complexity.

Why choose 3GEN Export for 1755031114 / 175-50-31114

Sourcing heavy undercarriage parts is not like buying small consumables. You need consistency, correct fit, reliable packing, and fast delivery—because the cost of machine downtime is often higher than the cost of the part.

3GEN Export supplies the 175-50-31114 EQUALIZER KOMATSU as an OEM-grade solution with a global logistics mindset. You get a part built for real-duty work and the export workflow to get it to your site quickly.

If you need additional photos, packing details, or combined shipping for multiple part numbers, 3GEN Export can support the request so your procurement stays simple and your maintenance work stays on schedule.

Manufactured in Turkey, these products are made using the latest technologies and built to meet the highest international standards. Each machine is a high-quality copy of the original, ensuring durability, precision, and performance that you can rely on for modern construction and metalworking projects.