
1755000024, 175-50-00024 EQUALIZER BAR KOMATSU
Description
1755000024 / 175-50-00024 EQUALIZER BAR KOMATSU (OEM Supply) When a dozer is working on rock, hard clay, or uneven haul roads, the undercarriage takes constant shock loads. The component that quietly manages a big part of that punishment is the equalizer bar. The 1755000024 and 175-50-00024 EQUALIZER BAR KOMATSU is designed to balance track-frame movement, reduce peak stress on the roller frame, and help keep the machine stable when one side of the track meets a different ground level than the other. At 3GEN Export, we supply this part as an OEM-quality solution built for consistent fit and long working life. We ship worldwide in 5 working days , with export-ready packaging to protect surfaces and mounting points during transport. What the 175-50-00024 Equalizer Bar Does in the Undercarriage The 175-50-00024 EQUALIZER BAR KOMATSU sits at the front undercarriage structure and acts like a mechanical “balancer” between the left and right track frames. In real-world operation, one track frame often climbs over obstacles while the other stays on flatter ground. Without an equalizer function, that uneven movement would transfer excessive twisting forces into the frame, mounting ears, and related joints. The 1755000024 equalizer bar helps: Distribute vertical loads across both sides of the undercarriage Reduce torsional stress on the main frame and track frames Maintain steadier contact between tracks and ground Improve operator control when grading, pushing, or ripping on uneven surfaces In short: the 175-50-00024 EQUALIZER BAR KOMATSU supports stability, protects structural components, and keeps undercarriage geometry operating as intended. Why Quality Matters for an Equalizer Bar This is not a “simple steel beam.” A high-performing equalizer bar must handle repeated shock loading, vibration, and cyclic stress without developing cracks, bore deformation, or surface wear that creates looseness at the joint. A properly produced 175-50-00024 EQUALIZER BAR KOMATSU should deliver: Accurate machining at pivot bores for controlled movement Robust metallurgy to resist fatigue cracking Strong surface integrity around stress zones (bends, transitions, bore areas) Coating/finish quality that reduces corrosion during storage and transport Because an equalizer bar affects alignment and load paths, a poor fit can accelerate wear in pins, bushings, brackets, and even the track frame assembly. Choosing an OEM-grade 1755000024 equalizer bar is a preventive step that protects more expensive undercarriage structures. Construction and Material Approach While exact metallurgical recipes vary by manufacturer and production batch, heavy-dozer equalizer bars are typically produced using high-strength steel with controlled toughness. The intent is to achieve a balance: hard enough to resist deformation at interfaces, tough enough to resist cracking under impact. An OEM-grade 175-50-00024 EQUALIZER BAR KOMATSU is generally engineered around: High-strength steel body designed for impact resistance Controlled processing to improve fatigue performance Machined pivot/bore areas for proper pin-and-bushing interface Smooth transition radii to reduce stress concentration This is why consistent production matters: undercarriage parts don’t fail from one overload; they often fail from thousands of micro-stresses. Key Wear Zones to Monitor If you’re replacing the 1755000024 equalizer bar, it’s usually because one or more wear patterns have reached a point where performance or safety is affected. The most common inspection points include: Pivot bore ovality Over time, the bore can become slightly oval due to movement under load, especially if lubrication intervals were missed or pins/bushings were already worn. Cracking at transition areas Look at curved or stepped geometry where the bar transitions from thick to thinner sections. These are typical fatigue zones if shock loading is severe. Surface damage at contact points Transport damage, corrosion pitting, or impact marks can become initiation points for cracks in hard service. When replacing the 175-50-00024 EQUALIZER BAR KOMATSU , it’s smart to check mating hardware (pins, bushings, seals, mounts) so the new bar isn’t forced to operate with worn counterparts. Installation Guide for 175-50-00024 EQUALIZER BAR KOMATSU Below is a practical, workshop-friendly installation outline. Always follow your machine’s official service procedures and safety rules. 1) Prepare the machine safely Park on stable, level ground Lower blade/attachments to relieve hydraulic pressure Lock out the machine and secure against movement 2) Support the undercarriage correctly Because the equalizer bar relates to track-frame movement, support must be done carefully to avoid binding. Use appropriate lifting equipment and rated stands. 3) Remove the old equalizer bar Mark alignment points before removal Remove retaining hardware (as applicable) Press or extract pins carefully (avoid mushrooming or bore damage) Inspect brackets/mounting ears for cracks or elongation 4) Inspect associated components Before installing the 1755000024 equalizer bar: Check pins and bushings for scoring, pitting, looseness Check seals and grease passages (where applicable) Verify bracket faces are clean and undamaged 5) Fit the new bar and align Clean and lightly lubricate contact surfaces (as recommended) Align bores without forcing; misalignment often means support points need adjustment Install pins and retention components per spec 6) Torque, secure, and test Tighten fasteners to correct torque values Confirm free movement (no binding) Perform a controlled operational check at low speed Re-check after initial working hours for settling or movement A correct installation of the 175-50-00024 EQUALIZER BAR KOMATSU should result in smooth articulation and reduced play at the joint. Operational Benefits You’ll Notice After Replacement Replacing a worn equalizer bar often improves the “feel” of the machine immediately, especially in hard ground. With a properly fitted 175-50-00024 EQUALIZER BAR KOMATSU , operators commonly report: More stable tracking on uneven terrain Reduced clunking/knocking sounds from front undercarriage movement Better blade control during grading Less visible frame twist over obstacles Lower risk of accelerated wear at pins/bushings due to looseness Compatibility: Which KOMATSU Models Use This Part Based on available seller fitment information, the 175-50-00024 EQUALIZER BAR KOMATSU is listed for KOMATSU DOZER D155A1 (Late) applications. Because Komatsu applications can vary by serial number range, undercarriage arrangement, and production year, you should confirm fitment using your machine’s model/serial details before ordering. If you share your machine model + serial range, you can validate the match before shipment. Weight (KG) One published listing shows a shipping weight of 714.3 lb , which is approximately 324.0 kg for the 1755000024 / 175-50-00024 EQUALIZER BAR KOMATSU . Technical Notes and Buyer Checklist When purchasing a 175-50-00024 EQUALIZER BAR KOMATSU , confirm these points to avoid downtime: Part number format: 1755000024 and 175-50-00024 (both should be recognized) Machine model and serial range validation Condition of mating pins/bushings (replace if worn to protect the new bar) Packaging requirements for international freight (wooden crate recommended) Delivery timeline and customs documentation readiness 3GEN Export supports export packaging and documentation for smooth cross-border delivery. Why Buy from 3GEN Export 3GEN Export is an OEM supplier focused on heavy machinery spare parts with logistics built for speed and reliability. With the 175-50-00024 EQUALIZER BAR KOMATSU from 3GEN Export, you get: OEM-grade production standard (fit, durability, consistency) Export-safe packaging options Fast worldwide dispatch and delivery in 5 working days Responsive support for part number verification and order handling FAQ Is 1755000024 the same as 175-50-00024? Yes, these are commonly used as alternate writing formats for the same item. Always match the number and confirm with your machine details. Do I need to replace pins/bushings too? If there is visible scoring, looseness, ovality, or corrosion, replacing them is strongly recommended. A new 175-50-00024 equalizer bar will wear quickly if installed with worn hardware. Can I install this part without special tools? Most workshops will need heavy lifting support, correct stands, and appropriate pin extraction/installation tooling. Avoid hammering methods that can damage bores or create misalignment. Manufactured in Turkey, these products are made using the latest technologies and built to meet the highest international standards. Each machine is a high-quality copy of the original, ensuring durability, precision, and performance that you can rely on for modern construction and metalworking projects.